Cable channel plugging holes through the wall cable company service hotline: 13961999789 Chow our patented technology: Polymer waterproof plugging, the Company and the professional waterproof anti-corrosion materials manufacturers and a number of national research institutions for many years developed a technology crystallization to more kinds of imported chemical materials, according to the construction of water pressure is almost the size of the ratio of the viscosity of water into the same liquid, good permeability, can be injected into the 0.1 mm slit in the concrete, quickly unite under the pressure and very humid environment. 2, setting time can be accurately controlled with the ratio within a few seconds or a few minutes, the rapid condensation of pressure in the water velocity, water flow and more cases. 3, good permeability, water swelling after drying shrinkage, insoluble in water, kerosene, gasoline and other organic solvents, acid, alkali, bacteria Erosion from atmospheric conditions also after, there is a certain strength, flexibility and change pressure, shelf use more than a decade. 4, tensile strength, Construction had been plugging the crack mouth, and later appeared normal settlement or dislocation cracks also no leakage. Seam leakage control program, Ltd. Jiangsu large waterproof plugging the cable trench wall hole plugging the cable company based on the actual situation of the project, you first need to crack grouting waterproof plugging leakage area, then flexible waterproof layer for fast again plugging Ling rigid waterproof protective layer construction. Plus flexible waterproof rigid protective waterproof plugging program is based on a national "underground works waterproof technical specifications" of seeking performed. Waterproof plugging, structural reinforcement construction procedures are as follows: 1, the first construction joints chisel a deep 70mm, 60mm width of a "V" seam, rinse with water. 2, the fixed channel and grouting grouting pipes fixed quickly plugging Ling grouting channel strip PE foam, PE foam strip at a fixed, every one about 50cm buried pipe grouting, grouting tube with 10 ~ 13mm of pressure rubber hose, the tube has been used as water pipes and as grouting works. 3, sealing and grouting plugging polysulfide flexible waterproof seal from the side of the start of construction of polymer injection grouting material - plugging Wang grouting, grouting pressure control between 0.3 ~ 0.5MPa, to be next to a grouting holes can stop take slurry grouting, and close the valve and then plugging the hole grouting from another, followed by the order, until all leaks observed grouting is completed, there are still some places such as leakage from the nearest A supplementary grouting hole until no leakage so far. Cut pipe before making PG321 component polysulfide sealant construction. 4, rigid protective layer construction when grouting waterproof plugging cracks will not produce leaks, with rapid plugging Ling made three rigid waterproof protective layer, a large area (cell) a leakage control program, the surface layer method: a large area suitable governance structure of water leakage. Under normal circumstances, a large area of ??the basement seepage water treatment can not be carried out the positive side, only in the dorsal surface treatment, it is in pre-construction, drainage should be cited, in order to prevent new surface layer is made of waterproof pressurized flush bad. Surface layer of concrete practice of law: Choose the amount of leakage centralized location, open hole borehole water flow from the catheter. According to the amount of the size of the leak can be in one or multiple water pipe, can not find the leakage point, in the lower part of the wall water pipe. Then watertight material requirements in accordance with the site, a large area smear polymer cement mortar waterproof need stratification TROWELING, order plain water slurry - waterproof mortar - Waterproof prime pulp, last dialed tube shutoff. For concrete slight seepage, plugging Ling available compression applied in the concrete surface, with a scraper construction, general construction of 2 to 3 times, but not until the water film so far. For obvious leakage of water holes and cracks, holes and cracks leakage by water treatment method, one by one waterproofing. For the structure of the surface of the concrete basement, water pressure in the smaller less severe slow leakage of water (such as sweating, Yin wet, etc.) can be anti-scratch coating on the back surface of the water leakage grams, so that the surface layer of impermeable cover layer impermeable to play the role. Specific practices: the primary surface treatment is smooth, rugged place filled with cement mortar, flatten trowel, while removing the primary surface dust, oil, etc., in order to facilitate the waterproof layer bonded firmly. After completion of the above work and pass the inspection, you can use anti-leakage grams construction. 2, grouting method: In case of a large area basement water leakage, grouting method may also be treated, can be arranged according to the grouting holes in the structure of water leakage case, the distribution into a plum-shaped, triangular or a shape, and then grouting treatment to form a water curtain in the internal structure. In addition, also the use of "closed surface grouting" approach, which is to water down the tube, and then a large area with rapid plugging Ling plaster, to be waterproof coating strength to meet the requirements, from the water pipe as Grouting. Four holes, point infiltration, embedded parts, wall pipe leakage control program (a) holes, point infiltration leakage control method, plugging method: using inorganic material plugging directly plugged. Encountered hole smaller or larger holes but slow leakage of water pressure is not the case, waterproof plugging inorganic materials can be directly plugged. Operating procedures: According to leak water situation, find out the leakage point to the leakage point as the center of boreholes (diameter of 1 ~ 3cm, depth of 2 ~ 5cm), the hole wall and the base surface perpendicular as possible, and rinse with water, by plugging material twisted into the shape of a similar hole cone-shaped group, let it start to solidify at the rapid pressure inside the hole, holes in the wall to squeeze around the dense, so plugging holes in the wall material and the close integration is completed by plugging check no water leakage, you can use polymer cement mortar pressed to the wall flush with the board or. 2, under the control law: for large hole pressure gushing rapids or water leakage. Specific practices are: the surface layer and bonded Clear leaks hollowing false stones, then tick into the hole, depending on the depth of the water may be leaking. Spread a layer of gravel in the bottom of the cave, the cover layer of gravel and hole the same size or linoleum sheet metal, and on which to open a small hole in the hose inserted into the hole, the water flowing along the tube, then use quick-setting materials The water pipe around the hole once filled, to be plugging material begins to solidify, forced to squeeze cement plugging holes around the dense clay surface and below the surface structure is not less than 1.5cm, clogging completed and no leakage of water through the examination After allocating hose, plug the hole, and finally with a sealant layered compression plate surface wiping pressure to flush. When the hole is large leak pressure, wedge, etc. can be used to plug the hole, the water stopped, and with the plugging material closure. After inspection and no leakage of water, polymer cement mortar or sealant for waterproofing layer compression. Governance holes leaking water can also be used caulking method, that uses the tick bath after plugging plugging sealing material, with two-component polysulfide sealant filling them with trenches, and finally even in other parts of the country as a waterproof layer. In addition, the pore structure of underground water leakage occurs, the method can be applied to plugging grouting, grouting can hole or holes drilled in the surrounding grouting. (B) embedded parts, wall pipe leakage control program 1, when embedded parts around the leak, which is an annular groove around the tick, remove embedded parts corrosion and erosion trench with water after plugging stuffer only water material, filled two-component polysulfide sealant or perfusion plugging slurry and other methods for processing. 2. When the ambient temperature around the wall (ground) water pipe leaks along the pipeline should be around the tick into the annular groove, after the water washed away with plugging material clogging tight, no leakage inspection after wiping the surface stratified pressure or compression of polymer cement mortar waterproof sealant flush with the base surface, caulking sealing material can also be used outside the scope of brushing pipeline 250mm waterproof coating, can be applied to perfusion plugging slurry manner. 3, for the pipeline through the interior parts of the leakage of water, can be expanded through holes chisel tick, then buried precast semicircle tube, pipe and casing in the gap at the two-component polysulfide sealant used to fill the casing blocked by plugging the gap at the outer material. Company conscientiously implement the ISO9001-2000, GB / T19001-2000 international quality system standards, Ltd. Jiangsu large waterproof plugging the cable trench wall hole plugging the cable company passed the safety, quality, occupational health and safety management system certification three . Construction of the project first inspection pass rate of 100% user satisfaction with the commitment of 100%, Ltd. Jiangsu large waterproof plugging the cable trench wall hole plugging the cable company for many years was awarded in recognition of the superior unit. Cable trench wall cable plugging holes