Baoding waterproof plugging your service Jiangsu large waterproof plugging plugging Engineering Co., Ltd. to undertake the following projects: elevator shaft plugging, plugging underground works waterproof, waterproof plugging pit, pit seepage, construction plugging, construction seepage, dam seepage plugging water leaks deck, roofing seepage, piping water sealing, basement sealing, basement waterproofing plugging, plugging mine, the cable channel plugging leak, waterproof plugging the cable trench, tunnel plugging, plugging tunnel waterproofing, waterproof plugging underground garage, concrete seepage water, waterproof plugging underground engineering, civil air defense projects seepage, cooling tower water seepage plugging, cooling tower leakage plugging, plugging waterproof expansion joints, seepage elevator shaft, elevator pit seepage, plugging water leakage elevator, pool plugging, plugging the pool water, sewage treatment pond water trap, thermal pipe anti- seepage plugging, plugging waterproof foundation engineering, structural joints seepage, construction joints waterproof plugging, drilling Wall plugging, concrete cracks leak water blocking, caisson foundation mending leakage, settlement leakage plugging, plugging seepage wells leak, waterproof plugging coal mine, coal mine seepage, cracks in the bottom leaking water, waterproof plugging the river tunnel, immersed tube tunnel plugging, plugging subway tunnel waterproofing, borehole seepage, highway tunnel seepage mine Wall waterproof plugging, plugging, plugging water, seepage, corrosion plugging, plugging the tunnel, with pressure plugging, plugging leaks, pool plugging, plugging underground civil air defense plugging, large dam plugging, plugging mine and other projects! Plugging technical process: plugging Chinese industry including the four sectors, namely "pressure plugging, plugging holes, waterproof plugging, plugging underground" four block industry, every industry in several technology, were introduced as follows: 1. Pressure Seal conduit vessels appear constantly lose pressure when corrosion perforation stop leaking leak does not get angry quickly plug the leak. Technical craft: 01, 02 Injecting sealing technology, bandaging strapping technology 03 Technology 04 cold welding stick up, clamp speed card blocking technology 05 Technology 06 strip tension, connection repair technique 07, high-frequency technology caulking 08, valve glue blocking technique 09, 10 Falanca with technology, burglary valve plug technology 2, the opening hole plugging closure: There are three technologies in the full name of the "do not get angry Tapping sealing industry" plugging holes industry, namely: no leakage intact transmission medium pipe or vessel wish to take a three-way valve does not get angry Tapping use technology, no leakage intact transport medium with pressure pipeline would like to replace the valves, flanges, or Let pipeline diversions need to use does not get angry with pressure sealing technology, no leakage intact delivery medium pipes are cut non-sparking called does not get angry with pressure pipe cutting. 3, waterproof plugging: waterproof plugging: This industry is responsible for plugging construction of houses, roofs, tunnels, subways, ditches, ponds etc. leaking. 4, downhole plugging: plugging underground: oil wells, wells fracturing and plugging. Professional undertaking: basement plugging, plugging the tunnel, cesspool plugging, culvert trap, plugging the pool, with water plugging, plugging the dock, mine plugging, cable channel plugging, plugging air defense projects, expansion joint sealing , joint sealing, plugging cracks off, pump plugging, settlement plugging, plugging the dam, underground works plugging, elevator shaft sealing, joint sealing works, cooling tower plugging, construction seam plugging, plugging and other underwater waterproof plugging. Plugging Note: First, water features water is pervasive, it is by air pressure, convection, impact, adhesion, capillary and other forces, and gradually penetrate inside the building, but also in the process of infiltration is not easy to find from the surface. In other words, to find the cause of leaking must better "visceral" analysis and judgment, to remedy. Second, water and water vapor pressure changes once the penetration into the building inside, in a limited space, and so on sun drying, to produce heat, to form water vapor, which vapor pressure is sufficient to produce a lot of damage to the original waterproof layer and even decoration and trim surfaces (such as, peeling paint, wallpaper black, tile muster, wooden floors swelling drums) In other words, a unit of water, if all turned into steam, inside the building limited space inside, it produces 1240-fold pressure, the pressure is too terrible destructive. (So ??we often find waterproof glue construction on aqueous foam cement, and soon the entire muster peeling off.) Third, the primary requirements and waterproof material followed by swelling of the interface must not have a drum, from the sand, honeycomb, wood, paper, sludge, small stones, can not do on the loose shaky table body, because poor adhesion, coupled with the sun's ultraviolet damage, thermal expansion and contraction of the building itself, as well as vapor pressure damage, is likely to cause the waterproof layer aging, failed. Fourth, the positive waterproof distinctions, such as roofing, done directly on the roof surface, the walls should be done directly in the external walls of waterproof, water leakage done directly in the inner tank, the water pressure would go elsewhere diffusion, the house where the dead is not easy construction. Here talked about "better" is relative comparison, rather than absolute in nature. Because with the development of technology, the market and more people to launch construction of the dorsal surface of waterproof material and high and low pressure injection of synthetic resin crystals produce expansion, also waterproof, but not all situations can be successful in construction, so the last resort, should adopt positive Waterproof construction. V. containment waterproof formula is easy to cure the root causes of failure should play from waterproof, with containment method, water is pervasive, it can cause stress damage, how can the root causes lasting died, for example: location leaky attic, just stamped illegally built inside the room, most people wanted to cut from the periphery as water, prone to failure. Sixth, regardless of the size o is defined as water pressure, regardless of the next few days of rain, and regardless of the roof, in short, the room paint not color, not bubbling. Seven, "at no cost water" concept to achieve the effect of water does not have to spend money, in addition to the occurrence of concrete "deterioration", the waterproof function itself. For example: previously covered house, wall tiles do not stick, stick stones but will not leak, and now houses the villa, made imports expensive waterproof coating later, there are still leaking occurred eight, no! a material of any kind is universal waterproof material has its uniqueness, applicability. "One size fits all" concept is wrong. So how to choose the material is an important issue, the good doctor is in the lead "medicine" instead of being "agents" led by the nose. "Select Yancheng Chen Heng plugging, so you no longer worry about leaking water seepage! Zhangjiakou professional waterproof plugging Welcome Phone: 0515-88281268 Fax: 0515-88938968 plugging Expert: Manager Zhou plugging Hotline: 13961999789 Baoding waterproof plugging your service